![]() ![]() Set csr-active-config to in your config.Morpholio Board is proud to feature the following "Interior Elite" and we thank them for their amazing design, innovation and support of a creative world.ġ5 West Studio 5mm.A SIP value which does not include the two flags above.csrutil disable -no-internal in Recovery.If you want to still have SIP disabled, use either: CSR_ALLOW_UNAUTHENTICATED_ROOT (Bit 11 = 0x800).CSR_ALLOW_APPLE_INTERNAL (Bit 4 = 0x10).Two bits in SIP specifically cause issues: Note: You do not need the -revsbvmm boot argument from RestrictEvents. More information is available on the Apple Secure Boot page (opens new window). If your SMBIOS does not have a T2 chip, then either Default or Disabled is ok. Hackintoshes which use a T2 SMBIOS MUST have OpenCore 0.7.4+ with SecureBootModel set to Default. non-T2 SMBIOS using j137 or iMacPro1,1 using j160). Starting with Monterey, updates are not delivered to T2 Macs which don't have Secure Boot enabled, and updates do not install properly if your SecureBootModel does not match your machine (ie. Monterey Beta 5+ issues (opens new window).If you still boot Big Sur or older, you can set the MinKernel field to 21.00.0 to prevent BlueToolFixup loading on older OSes.Needed for all non-native Bluetooth devices (Including Intel). ![]() BrcmPatchRAM2/3.kext + BrcmFirmwareData.kext for Broadcom.If you still boot Big Sur or older, you can instead set the MaxKernel field to 20.99.9 for your injector kext in your ist.BrcmBluetoothInjector.kext for Broadcom cards.IntelBluetoothInjector.kext for Intel cards.With the rewrite, injector kexts break bluetooth support in Monterey, though firmware uploader kexts are still needed. As of writing, many bluetooth devices do not work (legacy Broadcom and Intel). With Monterey, Apple has completely rewritten the bluetooth stack. Note that all cards have not been fixed yet, and that bluetooth support is being worked on still.ĭo not be suprised if your card does not work, and please be patient! For example, an 8-Core 5800X would have the new Replace value be:Ĭore Count => Hexadecimal Table Core Count Where is replaced with the physical core count of your CPU in hexadecimal. The patches which need to be edited are all named algrey - Force cpuid_cores_per_package, and you only need to change the Replace value. Haswell iGPUs are still supported in Montereyįor those on AMD CPUs, make sure to update your kernel patches (opens new window) for Monterey.ĭon't forget to update your patches as well with the core count of your CPU. Requires SIP, Apple Secure Boot, and AMFI disabled.You will lose access to non-full updates (Small 1-3GB updates).No support is provided for Hackintoshes using OCLP!.You can use OpenCore-Legacy-Patcher (opens new window) to add back support.Haswell laptops should use MacBookPro11,4 or MacBookPro11,5.Haswell desktops with only an iGPU should use iMac16,2.Haswell desktops with dGPU should use iMac17,1.Ivy Bridge desktops with dGPU should use MacPro6,1.If your SMBIOS was supported in Big Sur and is not included above, you're good to go! Supported SMBIOSĬlick here for a full list of supported SMBIOS.įor those on Haswell or Ivy Bridge, here are some simple conversions: MacBookPro11,4 and 11,5 are still supported.Getting started with ACPI (opens new window).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |